Milwaukee Tool
Milwaukee 1-1/8" X 16" SPLINE ROTOHAMMER BIT MWK 48-20-4112
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/8" SELF-FEED BITS MWK 48-25-1121
Milwaukee® selfeed drill bits deliver speed and Endurance for repetitive drilling of large holes. Designed for any trade that demands woodcutting for installing pipe and conduit, selfeed bits feed into work without pressure and provide faster boring of clean, accurate holes. The bits have improved balance with reduced runout, while the hex shank provides a secure gripping surface for the drill chuck. Every Milwaukee® selfeed drill bit is coated with a rust inhibitor. Built to last and designed to perform, these selfeed bits are resharpenable so you can keep them cutting like new.
Milwaukee 1-1/4"X22" SPLINE R/HAMM BIT MWK 48-20-4126
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/4" X 16" SPLINE ROTOHAMMER BIT MWK 48-20-4125
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/4" SELF-FEED BITS MWK 48-25-1252
Milwaukee® selfeed drill bits deliver speed and Endurance for repetitive drilling of large holes. Designed for any trade that demands woodcutting for installing pipe and conduit, selfeed bits feed into work without pressure and provide faster boring of clean, accurate holes. The bits have improved balance with reduced runout, while the hex shank provides a secure gripping surface for the drill chuck. Every Milwaukee® selfeed drill bit is coated with a rust inhibitor. Built to last and designed to perform, these selfeed bits are resharpenable so you can keep them cutting like new.
Milwaukee 1-1/4" MAGNETIC DRILL PRESS MWK 4208-1
This combination unit features the 4203 adjustable position, variable speed base and the 4297-1 1-1/4 in. drill motor. All you need is a bit and you are ready to drill into any ferrous material 1/2 in. and thicker.
Milwaukee 1-1/4" MAGNETIC DRILL PRESS MOTORS MWK 4292-1
This heavy duty unit is built for production drilling and will take the toughest drilling jobs. Model 4292-1 features an 11.5 amp motor with a no.3 morris taper chuck. This two speed unit has 375 and 750 RPM, geared low for maximum torque. Use the larger 4203 adjustable base for this powerhouse, and no job is too large.
Milwaukee 1-1/4" GUIDE PLATES MWK 48-20-6151
Increase your precision in masonry and concrete drilling with the Milwaukee® guide plate for thin wall core bit. You'll see reduced bit walk and improved bit stability when you use Milwaukee's durable plastic guide plate and centering pin (not included) for starting holes with your SDS plus rotary hammer drill.
Milwaukee 1-1/4" CARBIDE-TOOTH HOLESAW MWK 49-56-1253
Milwaukee® carbide tipped hole saws provide long life and faster cutting in cement board, ceramic tiles, fiberglass and wood products such as fiberboard, flake board and plywood. Use a carbide tipped pilot bit (49-56-8005) when cutting ceramic tile, brick and other abrasive materials.
Milwaukee 1-1/4" 120-VOLT REVERSIBLE DRILLS MWK 2404-1
The most hand-held power available in a specialty drill. Part of Milwaukee® super hole Shooter line, the 1-1/4 in large drill delivers versatile portable power for the toughest drilling and auger applications. The drill is furnished with a powerful Milwaukee® built motor and a #3 internal Morse taper socket. Poly chrome alloy steel gears produce high torque with minimum wear. You will get quiet performance from the heat treated, helical cut gears. The extra long switch handle and pipe handle provide maximum leverage and added control.
Milwaukee 1-1/2" X 22" SPLINE R/H BITS MWK 48-20-4151
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/2" X 16" SPLINE R/H BITS MWK 48-20-4150
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/2" V/CLEANER ASSY KITS MWK 49-90-1810
For less abusive environments where metal attachments are not required, this general purpose cleaning kit includes plastic attachments. The kit includes: 49-90-1865 chromed metal 2-piece floor wand, 49-90-1770 plastic crevice tool, 49-90-1775 6 in plastic utility nozzle, 49-90-1845 plastic 14 in squeegee insert, 49-90-1850 plastic 14 in carpet insert, 49-90-1840 plastic master floor tool, 49-90-1860 plastic round dust brush, 49-90-1855 plastic 14 in brush insert. Fits 1-1/2 in ID Hoses. All inserts snap lock into master floor tool.
Milwaukee 1-1/2" GUIDE PLATES MWK 48-20-6153
Use for starting a 1-1/4 in. hole drill to a depth of approximately 1/4 in., stop hammer, remove guide plate and center pin. Place core bit back into the grooved area and resume drilling to required depth of hole. Adds bit stability and reduces bit walk.
Milwaukee 1-1/2" DIA CONCRETE CORE BIT MWK 48-16-1507
1-1/2" DIAMOND CONCRETE CORE BITS-MWK48161507 >
Milwaukee 1-1/2" CARBIDE TOOTH HOLESAWS MWK 49-57-8227
Specifically designed for hand held operations in materials up to 3/8 in. thick, these Carbide tipped steel plate cutters stay sharper longer than high speed steel or bi-metal hole saws. They produce drill press quality holes even in hand held operations. For cutting materials over 3/8 in. up to a depth of 1/2 in., a drill press is recommended. When cutting depth is over 1/4 in., use Hawg Wash® cutting fluid to keep cutting surface cool and lubricated. Hawg Wash® fluid is available in 16 oz. Bottles (49-32-0081). One bottle makes one gallon of lubricating solution.
Milwaukee #6890 NIBBLER PUNCHES MWK 48-44-0260
This item is the replacement punch for Milwaukee's 16 gauge nibbler model 6890. The replacement die, 48-44-0270, is purchased separately. Must be used with plate wrench 49-96-4725 to remove the protective collar and 49-96-0330 2.5 mm wrench to remove the punch.
Milwaukee #6851 SPEED CONTROL SWITCHES MWK 23-66-1253
Milwaukee® 23-66-1253 Speed Control Switch, For Use With 6850 18 AWG Swivel Head Shear
Milwaukee #6480-20 PANEL SAW EXTENSION MWK 49-22-8108
The 49-22-8108 extension kit is used with Milwaukee's 6480-20 panel saw and is recommended whenever material over 6 ft. in length will be cut frequently. The kit extends the roller material carriage 18 in. on each end making the overall roller material carriage 8 ft. in length.
Milwaukee #6230 BANDSAW FRONT HANDLES MWK 31-44-0330
6230 BANDSAW FRONT HANDLE-MWK31440330 >
Milwaukee #5540 SANDER/POLISHER PADS MWK 49-36-2500
#5540 SANDER/POLISHER PAD-MWK49362500 >
Milwaukee #5192 DIE GRINDER TOGGLE SWITCHES MWK 23-66-2190
Milwaukee® 23-66-2190 Switch, For Use With 6805 Serial 709C 16 AWG Shear
Milwaukee #3 PHILLIPS BITS MWK 48-32-1070
#3 PHILLIPS SCREW-SHOOTER BITS-MWK48321070 >
Milwaukee #2 PHILLIPS SCREWDRIVERS MWK 48-22-2815
Featuring an anti-peel handle design, hardened tips & forged shanks the Milwaukee® cushion grip screwdrivers provide professional grade solutions and durability to the user. The tactile identification, a new-to-world innovation allows users to accurately select the correct driver without looking. The wrench-ready bolster and precision knurling offers users the features needed to increase efficiency and effectiveness.
Recently Viewed
Milwaukee® 48-20-5150 Heavy Duty Thick Wall Core Bit, 3-1/2 in Drill - Fraction, 3.5 in Drill - Decimal Inch, Carbide
Milwaukee's core bits are ideal for large hole drilling where depth is relatively shallow. The core bit cuts a Kerf only. The usable depth of thick wall core bits is 4-3/8 in.. the inside core must be removed by the operator before deeper drilling can be accomplished. The thick wall construction is ideal for larger hammers and more seasoned/cured concrete. A 7-1/2 in. extension is available to allow for the deeper holes to be drilled. The appropriate (Dependant on the diameter) Spline drive shank must be used to drive the core bit. Use 48-20-5199 center pin and 48-20-5173 guide plate for positioning and starting the hole. Thick wall core bits are available from 1 in. to 6 in. diameters. See thin wall core bits for less expensive drilling in new concrete and/or smaller hammers.
1/2" CENTER PUNCH 6" LENGTH - ALL25648 >
GEARWRENCH® 80548N Universal Impact Joint, Manganese Phosphate, 3/8 in Male Drive, 3/8 in Female Drive, ASME B107.2, Chrome Molybdenum Alloy Steel
GEARWRENCH offers a wide range of impact products in open stock & sets that are designed to deliver the performance and strength that the professional users require. They are made from chrome molybdenum alloy steel for exceptional strength and durability. Our sockets have a manganese phosphate coating to resist corrosion. The sockets also feature highly visible laser etched markings and a secondary size hard stamping. The sockets feature off-corner loading to reduce fastener rounding. The GEARWRENCH impact product family will allow the professional user to FORGE AHEAD.
When the days work is finished, you want to rest assured that your tools and equipment will be present the next day. In these times, security is a real concern. These rugged, lockable chests are the answer that many of our customers have been asking for.
4-40" NC CARBON STEEL PLUG TAPS-ITMC63NC0004>
3-AMP AUTOMOTIVE VIOLET BLADE FUSES
